400018 Serpent 411 Eryx 4.0 1/10 EP carbon 1/10 Àüµ¿Åõ¾î¸µ (Ä«º»¹öÁ¯)

Eryx 4wd TC 1/10 4.0 1/10 scale high end competition racing car for the international touringcar race series. Electric powered The Serpent ERYX ERYX 4.0 is the next big development stage for the 411 platform. Featuring an ultra low centre of gravity, optimized weight distribution, high performance geometry and top quality materials throughout, the ERYX is your car for personal best times ! This version has the carbon chassis 2.25mm

> Description

Serpent ERYX 4.0 introduction

The Serpent ERYX ERYX 4.0 is the next big development stage for the 411 platform. Featuring an ultra low centre of gravity, optimized weight distribution, high performance geometry and top quality materials throughout, the ERYX is your car for personal best times !

Michael Salven the Serpent chief onroad designer has worked intensively over summer with Marc Fischer and Viktor Wilck to develop the 4.0 new parts. Most of the testing was done by Marc and Viktor and the parts have been used in recent races already.

The Eryx 4.0 will ship end december worldwide.

Key new items in the ERYX 4.0
- new 2.25mm carbon chassis; fully symmetrical for even flex
- completely new shocksabsorbers; housing, lower cap, x-rings, machined bushings, shockrods, shockcaps, membrames
- 2mm higher front carbon shocktowers to mount the new shocks
- 2mm higher rear carbon shocktowers to mount the new shocks
- completely new mid-shaft pulley system with playfree assembly, one screw fixture
- new type one piece lower CG 7075 T6 motormount, centraly mounted
- adjustable carbon/alu battery supports to move battery front or back precisely, easily and securely
- steering-set with wider pivot system for more direct response
- improved diff gears for super smooth diff action
- New Onine PDF manual and ERYX 4.0 set-up sheet

New optionals
- rear lower suspensionpin mounts in 0.5 and 1.5, prepared to to be used with the innovative Reactive Rear Steering System
- carbon fibre chassis in 2mm hard and 2.25mm semihard versions

Key main specs
- Serpent springsteel front Double Joint Cardan shafts
- hard compound moulded suspension parts
- ball raced anti-roll bars
- centrally mounted servo-mount, lowest cg
- low friction belts and supertrue low friction pullies

Steering assembly
The Serpent ERYX utilises a centrally mounted ballraced dual pivot steering assembly-rack in aluminium. Offset steering linkage for correct steering geometry and ackermann. The steering assembly allows for very precise steering and great control. The ackermann is adjustable by using shims. The system pivots on wider low steering-shafts, creating a more direct steering feel. The bearing in the levers are pressed inside for a play-free assembly

Unique servo-holder
The unique and innovative servo holder has zero influence on tweak, as its floating above the chassis and mounted directly to the steering-assembly in the center of the car. This also keeps the weight lower than any other design.

Suspension brackets
For adjusting the cars toe-in and track-width, the ERYX is equipped with seperately mounted suspension brackets on both the front and rear of the car. Each bracket features an easily recognisable number that corresponds to the setting being used and due to the way they are mounted allows the user to easily and accurately adjust their cars settings. The brackets are designed such way that they can be used in any position in the car. The inner brackets FR and RR are now split type, to allow for more flex. The split suspension blcoks are mirror type, so you can use them either left or right and obtain a different desired setting. This way less different blocks are needed for a good variety of settings. Standard ones: : 3.5/ 0.5 split blocks in the rear, 2.0/ 0.5 in the front

DJC / CVD's spring-steel
This car is supplied with a complete set of 4 high quality hard coated spring-steel CVD shafts, which are a highly consistent, efficient and durable way to transfer all the power the surface. The front ones are v2 type double joint cardans DJC, the rear regular CVD style shafts.

Chassisplate
The newly designed very narrow chassis plate has been machined from 2.25mm carbon fibre . All holes in the base of the chassis have been countersunk .

The chassis further features extra holes to mount weights and additional stiffners . All holes are as close to the centerline of the chassis, to create even flex.

Battery-stays carbon / alu
The battery pack is kept in place by 2 mounts on the centreline of the car, and 2 special carbon/alu mounts with slits to mount the glass-tape. The carbon brace can be easily moved fronr or rearwarsd to move the battery more forward or backwards. Below these these the carbon Lipo battery holders are mounted.

Belts - drivetrain
The ERYX features a 2-belt configuration with a long front and a short rear Kevlar reinforced low friction belt that combied with precision moulded gears makes for a super smooth and free drive train.

Shocktowers
The Serpent ERYX features lowered shocktowers 2.5mm thick carbon fibre shock towers on the front and rear of the car. Each tower sports many holes for adjustment of the shock absorber angle while the rear tower also acts as the mount for the rear body posts and the front tower accommodates a 3rd front body post.

Spool
The car comes supplied with a front spool which has been made from hard anodised aluminium and are used with blades to increase lifspan. The shape has been optimised to ensure that the part is as light as possible without compromising strength.

Anti-roll bars
The ERYX is supplied with coded anti-roll bars front and rear with a composite centering bracket. The anti-roll bars are available in a number of thicknesses and are connected to the wishbones using short adjustable track rods, connected with a pivot ball to the lower front wishbone, and with a ball directly to the rear lower wishbone.
The anti-roll bars run in small tapered nylon inserts , and the anti-roll bar is centered through one captured center bushing.

Harder C-hub front
A standard system on most high-end touring cars, the ERYX features a front C-hub system in Hard composite. The car comes standard with a 4-degree caster block but is also supplied with a pair of 2 and 6-degree blocks. The C-hub is large enough to take out the drive-shaft assembly without dis-assembling the c-hubs.

Front suspension
Similar to the rear suspension in configuration, the front suspension sports a lower composite wishbone while the upper camber adjustment is handled using an aluminium track rod which is solid, lightweight and can easily handle impacts.

Rear section with harder arms
The rear end of the ERYX features stronger Hard lower wishbones . The lower wishbones can be used on both the left and right sides, minimizing the number of spare parts needed to bring to the track. The rear Hard upright features a pivot pin mounting point on the bottom and 2 upper camber link mounting holes for fine-tuning camber rise.

Indentical
The front and rear end of the Serpent ERYX are fully indentical and been designed for high performance and ease of maintenance. The rear bearing blocks have been designed in 2 pieces which allows the topside to be simply removed with 4 screws, giving you easy access to the differential for maintenance or adjustment. All the parts have been machined from aluminium and are anodized in gun metal grey.

Central section
The new one piece machined aluminium motorbracket is superlight and superlow and suits both stock and mod gearing well. The small front alu bracket, can be fitted with an alu bushing with long screw to connect to the top-deck. It can also be removed to create extra flex. The seperate machined brackets hold the light aluminium middle shaft/ 19T pulley.

Composite Gear differential with new material composite gears and X-axle
The ERYX comes supplied with a lightweight and smooth rear gear-differential. This supersmall differential can handle all the power of BL motors. Gear-diff can also be used on the front. The new version has new type composite internal gears and 3.5mm x-shape shaft and features coated aluminium outdrives. The metal gears can also still be used or mixed with composite. ( The ball-diff is optional).

Big bore shocks
The new Serpent bigbore onroad shockabsorbers lower the center of gravity even further. They come with threaded coated shock-bodies, pre-load shock nuts with o-ring, harder membrames , supersmooth and strong shock-rods with clip to hold the piston, perfectly machined pistons ( 1,2,3 and 4 holes in kit) in a new yellow material , toplevel x-ring /bushing package, light spring-cups, strong balljoints. The advantage is that you can continue using the normal size springs as before.

High quality race-springs included with color coding, grinded flat for even load.

Bumper
The front bumper has been made from a high impact absorbing foam material and is shaped to protect the entire front end of the car in the event of a crash. The bumper is held in place with a large top-plate.

Ball-bearings
The ERYX is supplied with high-quality lightweight bearings with orange seals throughout, making the drive train very efficient and allowing it to run very smoothly.

Set-up
Ackermann: two positions on the steering blocks , and the steering plate with shims
Camber: adjustable front and rear
Toe-in: adjustable front and rear
Front Caster: 4¡Æ static ( 0¡Æ, 2¡Æ or 6¡Æ as optional )
Downstops: adjustable front and rear
Front anti-dive: adjustable range 0¡Æ to 3¡Æ
Rear anti-squat: adjustable range 0¡Æ to 3¡Æ
Anti-roll bars: 1.4mm front and 1.4mm rear

Packing
The ERYX kit comes without body/wheel/tyres/spurgear and electronics. Its packed in a very small strong box with nice graphics, which can be re-used as parts or tyre box lateron. The box contains bags which are numbered in same sequence as steps in the manual.

Manual / decal / set-up sheet
To allow you to build your car with the greatest of ease, Serpent supplies a full colour PDF online instruction manual and integrated reference guide section that contains all the exploded views and latest options. Serpent logo decal sheets and set-up sheet are included .
All Manuals are available to download as a PDF in the Download section of this product page.
www.serpent.com/400017

> Specifications

Class: 1/10th scale 190mm Electric
Purpose: 190mm Competition touring car
Chassis: 2mm 7075 T6 aluminium, anodised, CNC machined
Suspension: Front C-Hub suspension system
Rear axle: Rear gear- differential with composite gears
Front axle: Front spool with blades
Drive system: 4wd through 2 kevlar reinforced timing belts
Shock absorbers: Super-Short RCM shock absorbers
Wheel base: 254mm +/- 4mm
Track-width front: 190mm /- 6mm
Track-width rear: 190mm /- 6mm
Adjustability: Camber, Caster, Down-stops, Up-stops, Toe-in, Track width & Roll centres
: Full colour PDF instruction manual and reference guide
Instructions: Motor, battery, speed Controller, tires, body, radio equipment.